How much does CNC machining cost?
Setup and programming, paid once per part line, plus machine time and material on every part, plus any finish and paperwork you add. Below are our hourly rates and what two test parts cost, worked out from the same price list as our instant quote.
Our hourly rates
What you pay an hour, in Canadian dollars before tax and shipping. Every instant price is worked out from these.
| Machine or work | An hour |
|---|---|
| Rates load from the live price list. | |
Machine time is the minutes a part spends on its machine, loading and unloading included, at that machine’s rate. Setup and programming covers programming the part and setting up each side, once per part line: once for each different part on an order. Checking the first part and measuring every part are billed at the 3-axis rate.
One part or a hundred
These are two of the test parts we check our quote engine against, not customers’: a bracket, 80 × 60 × 18 mm, milled from the top and the bottom with one tapped M5 hole and two counterbored ones, and a shaft, Ø40 mm at its widest and 75 mm long, turned on the lathe with a Ø10 mm hole in one end. Both are 6061-T6 aluminum, at standard tolerance, 10 business days, as machined. Prices are in Canadian dollars, before tax and shipping.
| Quantity | Bracket, each | Shaft, each |
|---|---|---|
Prices load from the live price list.Upload a model | ||
The first part carries the whole setup. Setup and programming are paid once per part line: about for the bracket and for the shaft. Once that’s paid, each further part adds only what it takes to make it: about for a bracket and for a shaft.
That’s why a single prototype costs so much more than each part of a low volume run, and why the price each falls fastest over the first ten.
Which machine, and what it costs an hour
The instant quote picks the machine from your model:
- Lathe, an hour. A part that’s round about one axis, with at least 97% of its surface turned about it, goes on the lathe if it fits: from round bar, in two setups, one for each end. See CNC turning.
- 3-axis mill, an hour. Most other parts. It cuts from one side at a time, and each side is a setup to hold, load and program. See CNC milling.
- 5-axis mill, an hour. A part with freeform surfaces, and a part that needs four sides or more on the 3-axis when the 5-axis, in two setups at most, comes out cheaper. It reaches up to five sides in one setup, but costs more an hour and takes longer to program.
The bracket needs two sides, so it stays on the 3-axis. The shaft is round, so it goes on the lathe. The machinist who checks the quote can still move a part to another machine, and the firm quote prices it there.
What tolerance, lead time, finish and paperwork add
The prices above are at the quote’s defaults: standard tolerance, 10 business days, as machined and no paperwork. Ten brackets cost and ten shafts . Each choice below, on its own, adds to the price of ten:
| Choice | Ten brackets | Ten shafts |
|---|---|---|
| Prices load from the live price list. | ||
- Tolerance. Holding ±0.001" instead of ±0.005" runs the finishing passes slower, and each part takes longer to measure.
- Lead time. Expedited, in 5 business days, costs 1.25 times the machining and programming, and rush, in 3, costs 1.5 times.
- Finish. Type II anodize adds for the lot, a part and 4 business days. The lot charge is paid once an order for each finish, whatever the quantity.
- Paperwork. Material certs, a CMM inspection report and a first article report are paid add-ons; take what your job needs. Certs are a part line, the CMM report plus measuring time on the first five parts, and the first article report a part line. The first article report adds a business day.
The same part in each material
Ten of each, everything else at the defaults:
| Material | Bracket, each | Shaft, each |
|---|---|---|
| Prices load from the live price list. | ||
Stainless and titanium cut slower, and titanium itself costs more. The quote also prices 7075 aluminum, C110 copper, 4140 prehard steel and 316 stainless.
How to bring the price down
- Fewer sides. On a 3-axis mill each side is a setup, programmed once and loaded on every part. Put features on the top and bottom where the design allows. The test manifold on our milling page is drilled from three sides; moving one side’s features to the top or bottom saves about on ten.
- Bigger inside corners. A round cutter leaves its own radius in each inside corner, and it cuts cleanly about 3 of its diameters deep. A tight corner deep in a pocket takes a smaller cutter stepping down in slow passes, on every part. See inside corner radius.
- Standard tolerance. Hold ±0.001" only on the features that need it, and mark them on the drawing. The rest at ±0.005" cuts and measures faster. Precision on the whole of the ten brackets adds .
The design checks run on every model as you add it, and the quote in your dashboard suggests changes like these for your own part, with what each saves. The full list of checks is in our design guidelines.
Why the instant price is a range
The instant price is worked out in your browser from your model, so it shows a likely range, 15% either side: for the ten brackets, to . A machinist checks every quote within one business day, with your drawing if you add one, and decides how the part is really made. The firm quote is the price you pay.
Questions
Do prices include tax and shipping?
No. Every price here and in the quote is in Canadian dollars, before tax and shipping.
Are there setup fees?
Setup and programming are paid once per part line, and they’re inside the price, not added on top. The quote spreads them over the parts you order, and its price breakdown shows them.
Is there a minimum order?
Yes: an order, before tax and shipping. A single part is fine: an order under the minimum is brought up to it, and the quote shows the difference on its own line. Each part also carries a minimum material charge: .
Upload a model and see the price in Canadian dollars, or book a call and talk it through with a machinist.