Milled parts3-axis and 5-axis, priced from your model

CNC milling services

3-axis and 5-axis CNC milling for custom machined parts, in our partner shop in Canada: brackets, plates, covers, housings and manifolds, from one prototype to a few hundred. Aluminum, copper, brass, steel, stainless steel, titanium and acetal, up to 1016 × 508 × 508 mm, held to ±0.005" and shipped in ten business days as standard. Upload a STEP file and the instant quote counts the sides your part needs and picks the machine.

On a 3-axis mill, every side is a setup

The quote reads from your model which sides a cutter has to reach. Each side is a setup: the part is held a new way, loaded and programmed for that side. A plate, a cover or a bracket usually needs two, the top and the bottom. Holes or pockets in an end or an edge add a third. Setup and programming are paid once per part line, and loading each setup is paid on every part, so every side adds to both.

When a part needs three sides or more on the 3-axis, its quote suggests fewer sides to machine and shows what moving the features on one side to the top or bottom would save. A part that’s round about one axis goes on the lathe instead, from round bar in two setups; see CNC turning. Either way, a machinist checks the quote within one business day and decides how the part is really made. The firm quote is the price you pay.

A worked example: what a milled bracket and manifold cost

These are two of the test parts we check our quote engine against, not customers’: a bracket, 80 × 60 × 18 mm, machined from the top and the bottom, and a manifold block, 60 × 40 × 30 mm, drilled from three sides. Both are 6061-T6 aluminum. Holes at a tap drill size are taken as tapped, as the quote takes them: one M5 in the bracket, an M6 and four M8 in the manifold. Standard tolerance, ten business days, as machined. Prices are in Canadian dollars, before tax and shipping.

The two test parts’ price each, by quantity: a bracket machined from two sides and a manifold from three
QuantityBracket, eachManifold, each
Prices load from the live price list.Upload a model

The manifold fits in a smaller block, and it costs more. Setup and programming are paid once per part line, and the manifold’s third side is one more setup to hold, load and program, with two thread sizes to set up as well. Then each part takes machine time: by the quote’s estimate, 14.4 minutes for the bracket and 16.7 for the manifold, its tapping included.

That’s also why one part costs so much more than ten: the first part carries the whole setup.

Upload the manifold and the quote suggests fewer sides to machine.

When a part goes on the 5-axis mill

A 3-axis mill cuts from one side at a time. A 5-axis mill reaches up to five sides in one setup, but it costs more an hour and takes longer to program, so the quote puts a part there in two cases:

  • Freeform surfaces. A part with sculpted, freeform surfaces is priced on the 5-axis.
  • Four sides or more. A part that needs four or more sides on a 3-axis mill is priced both ways, in two setups at most on the 5-axis, and the lower price wins.

The bracket and the manifold need two sides and three, so both stay on the 3-axis. The machinist who checks the quote can still move a part from one machine to the other, and the firm quote prices it there.

What moves the price

The same bracket, ten of them:

  • Material. Stainless and titanium cut slower, and titanium itself costs more.
  • Tolerance. Holding ±0.001" instead of ±0.005" costs more. The finishing passes run slower and each part takes longer to measure.
  • Lead time. Five business days costs 1.25 times the machining and programming, and three days costs 1.5 times.
  • Finish. Type II anodize adds 4 business days.
  • Paperwork. Material certs, a CMM inspection report and a first article report are paid add-ons; take what your job needs.

The instant price shows a likely range, 15% either side.

Our hourly rates for each machine are on CNC machining cost.

Designing a part for the mill: corners, pockets, walls

The design checks run on every model as you add it; the full list is in our design guidelines. The ones milled parts meet most:

  • Inside corners. A round cutter leaves its own radius in every inside corner. Make it at least 1/8 of the pocket’s depth. Where you don’t give one, we leave about R1.5.
  • Pockets. A pocket up to 4 times as deep as it is wide cuts cleanly. Past 10 times, widen it or make it shallower.
  • Thin walls. Keep walls over 0.8 mm in aluminum, steel, brass and copper, 1.0 mm in stainless and titanium, and 1.5 mm in plastics. In 7075, floors and walls under 1.5 mm can bow 0.1 to 0.5 mm once they’re cut free.
  • Reach. Undercuts and faces hidden from every side need a 5-axis or a special cutter, or can’t be cut at all. Open them to one side where you can.

Milling materials and finishes

Aluminum 6061-T6 and 7075-T6, copper C110, brass C360, steel 1018 and 4140 prehard, stainless 304 and 316, titanium grade 5, and acetal (Delrin).

Finishes, with the business days each adds: bead blast (1), type II anodize (4) and hard type III anodize (5) on aluminum, tin plate on copper and brass (5), black oxide on steel (3), passivate on stainless (2), and powder coat (4). Bead blast and powder coat aren’t offered on plastics.

Who makes it

Highland quotes and manages every order. The milling happens in our partner shop in Canada, which is registered to ISO 9001:2015, and your NDA covers the shop before it opens your file. Parts ship across Canada and to the US. For a Canadian customer there’s no border to cross and no customs brokerage.

Questions

What’s the largest part you can mill?

Up to 1016 × 508 × 508 mm. The instant price sends a bigger part to a machinist, who quotes it.

How fast can I get parts?

They ship in 10 business days as standard, 5 expedited and 3 on rush, plus the days a finish adds.

What files work?

STEP, IGES, Rhino (3DM) and ACIS (SAT) price instantly. STL and DXF work too. Add the drawing as a PDF or a photo so tolerances and threads get checked.

Do you do sheet metal or 3D printing?

No, neither is offered. Every part is machined.

Upload a model and see the price in Canadian dollars, or book a call and talk it through with a machinist.