Turned partsPriced on the lathe, from your model

CNC turning services

Round parts turned on a CNC lathe in our partner shop in Canada: shafts, bushings, spacers, flanges and adapters, from one prototype to a few hundred. Aluminum, copper, brass, steel, stainless steel, titanium and acetal, held to ±0.005" and shipped in ten business days as standard. Upload a STEP file and the instant price puts a round part on the lathe by itself.

When a part goes on the lathe

If the part is round across one axis, and at least 97% of its surface turns about that axis, it is priced on the lathe: from round bar, in two setups, one for each end. The bar is the part plus 3 mm a side, so a Ø40 × 75 mm shaft is cut from Ø46 × 81 mm bar.

A round part too big for the lathe goes to the mill, or to a machinist if it outgrows the mill too. A part with flats, cross holes or milled pockets over more than 3% of its surface goes to the mill. Either way, a machinist checks the quote within one business day and decides how the part is really made, mill-turn included. The firm quote is the price you pay.

A worked example: one shaft, two machines

This is one of the test parts we check our quote engine against, not a customer’s: a stepped shaft in 6061-T6 aluminum, Ø40 mm at its widest and 75 mm long, with a Ø10 mm hole 18 mm deep in one end. Standard tolerance, ten business days, as machined. Prices are in Canadian dollars, before tax and shipping.

The test shaft’s price each, by quantity, on the lathe and milled from a block
QuantityOn the lathe, eachMilled from a block, each
Prices load from the live price list.Upload a model

Two things make the difference. Setup and programming are paid once per part line, and the lathe needs two setups where the mill needs three. Then each part takes machine time: by the quote’s estimate, 6.3 minutes on the lathe against 12.1 on the mill.

That’s also why one part costs so much more than ten: the first shaft carries the whole setup.

What moves the price

The same shaft, ten of them, on the lathe:

  • Material. Stainless and titanium cut slower, and titanium bar costs more.
  • Tolerance. Holding ±0.001" instead of ±0.005" costs more. The finishing passes run slower and each part takes longer to measure.
  • Lead time. Five business days costs 1.25 times the machining and programming, and three days costs 1.5 times.
  • Finish. Type II anodize adds 4 business days.
  • Paperwork. Material certs, a CMM inspection report and a first article report are paid add-ons; take what your job needs.

The instant price shows a likely range, 15% either side.

Our hourly rates for each machine are on CNC machining cost.

Designing a turned part: holes, threads, walls

The design checks run on every model as you add it; the full list is in our design guidelines. The ones turned parts meet most:

  • Holes in the end. A drill is fine to 6 times its diameter deep. Past 12 times, standard drills don’t reach. The shaft’s Ø10 hole is under 2 diameters deep.
  • Threads. A tapped hole needs enough length to hold a screw’s full strength: 1.5 times the thread diameter in aluminum (9 mm for M6), 1.2 times in steel, stainless and titanium, 1.6 times in brass and copper, 2.5 times in plastics.
  • Thin walls. Thin-walled tubes and bushings chatter. Keep walls over 0.8 mm in aluminum, steel, brass and copper, 1.0 mm in stainless and titanium, and 1.5 mm in plastics. Under 0.5, 0.6 and 1.0 mm they may not survive being cut.
  • Long and slender. A part more than 8 times as long as it is wide bends under the tool. Widen it where you can.

Turning materials and finishes

Aluminum 6061-T6 and 7075-T6, copper C110, brass C360, steel 1018 and 4140 prehard, stainless 304 and 316, titanium grade 5, and acetal (Delrin).

Finishes, with the business days each adds: bead blast (1), type II anodize (4) and hard type III anodize (5) on aluminum, tin plate on copper and brass (5), black oxide on steel (3), passivate on stainless (2), and powder coat (4). Bead blast and powder coat aren’t offered on plastics.

Who makes it

Highland quotes and manages every order. The turning happens in our partner shop in Canada, which is registered to ISO 9001:2015, and your NDA covers the shop before it opens your file. Parts ship across Canada and to the US. For a Canadian customer there’s no border to cross and no customs brokerage.

Questions

My part is turned but has a milled flat or a cross hole. Can you make it?

Yes, we make mill-turn parts. The instant price runs a part like that on the mill, and the machinist who checks it sets how it’s really made before the firm quote.

What files work?

STEP, IGES, Rhino (3DM) and ACIS (SAT) price instantly. STL and DXF work too. Add the drawing as a PDF or a photo so tolerances and threads get checked.

How many parts can you make?

One prototype to a few hundred.

Upload a model and see the price in Canadian dollars, or book a call and talk it through with a machinist.